Cooper Bussmann 5073E-T Bedienungsanleitung Seite 88
- Seite / 106
- Inhaltsverzeichnis
- FEHLERBEHEBUNG
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
88 www.cooperbussmann.com/wirelessresources
Cooper Bussmann 5073E-T Managed Ethernet Switch User Manual
Rev Version 1.1
Ping Command
CLI Commands Level Description Example
ping
[ip]
E Ping function. switch>ping 192.168.1.1
Port Control Commands
CLI Commands Level Description Example
interface fastEthernet
[Portid]
G Choose the port for modification. switch>enable
switch#configure
switch(config)#interface fastEthernet 2
state
[enable|disable]
I Use the state interface configuration
command to specify the state mode
of operation for Ethernet ports. Use
the disable form of this command to
disable the port.
switch>enable
switch#configure
switch(config)#interface fastEthernet 2
switch(config-if)#state disable
duplex
[full | half]
I Use the duplex configuration
command to specify the duplex mode
of operation for fast Ethernet.
switch>enable
switch#configure
switch(config)#interface fastEthernet 2
switch(config-if)#duplex full
speed
[10|100|1000|auto]
I Use the speed configuration
command to specify the speed mode
of operation for fast Ethernet. The
speed cannot be set to 1000 unless
the port is a giga port.
switch>enable
switch#configure
switch(config)#interface fastEthernet 2
switch(config-if)#speed 100
flowcontrol mode
[symmetric|asymmetric]
I Configure flow control. switch>enable
switch#configure
switch(config)#interface fastEthernet 2
switch(config-if)#flowcontrol mode
asymmetric
no flowcontrol I Disable flow control of interface. switch>enable
switch#configure
switch(config)#interface fastEthernet 2
switch(config-if)#no flowcontrol
security enable I Enable security. switch>enable
switch#configure
switch(config)#interface fastEthernet 2
switch(config-if)#security enable
no security I Disable security. switch>enable
switch#configure
switch(config)#interface fastEthernet 2
switch(config-if)#no security
auto-sfp
[Enable|Disable]
G Enable or disable auto detect
100/1000 SFP.
switch>enable
switch#configure
switch(config)#auto-sfp disable
- Cooper Bussmann 1
- User Manual 1
- Release Notice 3
- Follow Instructions 3
- Proper Use 3
- CONTENTS 4
- 5Rev Version 1.1 5
- ChapTEr 1 - INTrODUCTION 6
- 1.3 Order Information 7
- 1.4 Hardware Features 7
- 1.5 Software Features 8
- 1.6 Package Contents 9
- 2.1 Front Panel 10
- 2.2 Top View 11
- 2.3 LED Indicators 11
- 3.1 Installation Steps 13
- 3.2 DIN Rail Mounting 13
- 3.3 Wall Mount Plate Mounting 14
- 3.4 Wiring the Power Inputs 15
- 3.6 Cabling 16
- 17Rev Version 1.1 17
- 4.1 Pro-Ring2se Application 19
- 5.2 Pin Assignment 21
- 5.4 CLI Management 23
- 6.2 System Login 24
- 6.3 Web Page Overview 25
- 6.4 System Menu 25
- CPU Load Average 26
- 6.4.2 Time - SNTP 27
- 29Rev Version 1.1 29
- 6.4.3 Account - Admin 30
- 6.4.4 IP Addressing – IPV4 30
- 6.4.5 Syslog 31
- 6.4.6 SNMP 32
- SNMP Trap Configuration 33
- 35Rev Version 1.1 35
- 37Rev Version 1.1 37
- 6.4.7 System Alert 38
- System Alert Event 39
- Digital Input/Digital Output 40
- 41Rev Version 1.1 41
- 6.4.8 DHCP Server 42
- DHCP Server Client Table 43
- DHCP Server IP Binding 43
- 6.5 Configure Menu 44
- Port Status 45
- Port Statistics 45
- Port Alert 46
- 6.5.2 Rate Control 47
- Storm Control 48
- 6.5.3 Aggregation 49
- 6.5.4 Spanning Tree 50
- RSTP Settings 51
- RSTP Information 52
- 53Rev Version 1.1 53
- 6.5.6 Multicast Support 54
- IGMP Snooping 55
- Static Filtering 55
- 6.5.7 LLDP 56
- 6.5.8 Filtering Data Base 57
- 6.5.9 VLAN 58
- 59Rev Version 1.1 59
- 61Rev Version 1.1 61
- VLAN Switch Status 62
- 6.5.10 QoS 63
- Port Priority 64
- COS Mapping to Queue 64
- 6.5.11 Port Mirroring 65
- 6.6 Security Menu 66
- Static Table 67
- 6.6.2 802.1X/Radius 68
- 802.1X/Radius Port Setting 69
- 802.1X/Radius Port Status 69
- 6.6.3 MAC Filtering 70
- 6.7 Maintenance 71
- 6.7.2 Restart Device 72
- 6.7.3 Factory Defaults 72
- 6.7.4 Firmware Upgrade 72
- 6.7.5 Export/Import 73
- 6.7.6 Diagnostics 75
- 6.8 Troubleshooting 76
- 77Rev Version 1.1 77
- 10 /100BASE-TX Pinouts 78
- RJ-45 Pin Assignments 78
- 10/100Base-TX Cable Schematic 78
- 10/100/1000Base-TX Pinouts 79
- 802.1x Commands 80
- Admin Password Commands 81
- Backup and Restore Commands 81
- CLI Commands 82
- DHCP Server Commands 82
- Factory Default Command 83
- Fault Alarm Commands 83
- IGMP Commands 84
- IP Security Commands 85
- IP Setting Commands 85
- LLDP Commands 86
- Loading Average Commands 86
- Logout Command 86
- MAC Address Table Commands 86
- MAC Blacklist Commands 87
- Ping Command 88
- Port Control Commands 88
- Port Monitoring Commands 89
- Port Security Commands 89
- Port Statistics Commands 90
- Port Status Command 90
- Pro-Ring2se Commands 90
- Rate Limit Commands 91
- RSTP Commands 92
- Save Configuration Command 93
- SFP Monitor Command 93
- SNMP Commands 93
- SNTP Commands 94
- Switch Setting Commands 94
- System Event Log Command 95
- System Reboot Command 95
- System Warning Commands 95
- Trunk Commands 97
- Upgrade Firmware Command 97
- VLAN Commands 98
- 99Rev Version 1.1 99
- Rev Version 1.1 100
- 101Rev Version 1.1 101
- 103Rev Version 1.1 103
- Term Definition 104
- ©2013 Cooper Bussmann 106
- Rev Version 1.1106 106
Verwandte Produkte und Handbücher für Vernetzung Cooper Bussmann 5073E-T
(4 Seiten)© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.034 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern